Visit sensors section to learn more about sensors configuration.
Auto detection
Server detects available device sensor parameters automatically, but user should configure them manually. This allows user to choose which sensors to monitor.
- Make sure all needed sensors are connected to GPS device, for example: ignition, doors, fuel, inputs, outputs and etc.
- Drive your vehicle, turn on and off ignition, open and close doors and so on.
- Server will auto learn and detect all possible sensor parameters.
- Detected sensor parameters will appear in sensor properties Parameter select box.
Description
Below are listed most common sensor parameter names, still they vary depending on GPS device model and capabilities.
| Sensor | Description | Possible values |
| alaX | ala – Alarm, X refers to alarm number | 0 = no alarm, 1 = alarm |
| acc | ACC status | 0 = off, 1 = on |
| accv | ACC voltage | Value |
| batl | Battery level | Value |
| batp | Battery percentage | Value |
| batv | Battery voltage | Value |
| bats | Battery status | 0 = not charging, 1 = charging |
| diX | di – Digital Input, X refers to input number | 0 = off, 1 = on |
| doX | do – Digital Output, X refers to output number | 0 = off, 1 = on |
| aiX | ai – Analog Input, X refers to input number | Value |
| aoX | ao – Analog Output, X refers to output number | Value |
| canX | can – CAN port data, X refers to CAN port number | Value or String |
| tempX | t – temperature, X refers to temperature meter number | Value |
| fuelX | fuel – Fuel level, X refers to fuel meter number | Value |
| pump | Fuel pump status | 0 = off, 1 = on |
| ibut | iButton for driver ID | String |
| rfid | RFID for driver ID | String |
| odo | Absolute odometer in km | Value |
| odor | Relative odometer in km (between two records) | Value |
| engh | Absolute engine hours | Value |
| enghr | Relative engine hours (between two records) | Value |
| gsmlev | GSM signal level, signal strength | Value |
| gpslev | GPS signal level, number of satellites | Value |
| hdop | HDOP | Value |
| pdop | PDOP | Value |
| vdop | VDOP | Value |
| track | If device is in tracking mode or not | 0 = no, 1 = yes |
| sleep | If device is in sleep mode or not | 0 = no, 1 = yes |
| move | If device is moving or not | 0 = no, 1 = yes |
| accel | Accelerometer status | 0 = no, 1 = yes |
| dlog | Data logging status | 0 = no, 1 = yes |
| balance | SIM card balance | String |
| lac | GSM Location Area Code | String |
| cellid | GSM Cell ID | String |
| mcc | MCC | String |
| mnc | MNC | String |
| can_sysev | CAN system event | String |
| can_vemot | CAN vehicle motion | String |
| can_clus | CAN clutch pedal state | String |
| can_bres | CAN break pedal state | String |
| can_accs | CAN acceleration pedal state | String |
| can_crus | CAN cruise control state | String |
| can_ptos | CAN PTO state | String |
| can_enplcs | CAN engine PLCS | String |
| can_tyreloc | CAN tire location | String |
| can_axlew | CAN axle weight | String |
| can_axloc | CAN axle location | String |
| can_haninf | CAN handling information | String |
| can_dirind | CAN direction indicator | String |
| can_flev | CAN fuel level | String |
| can_fcr | CAN fuel consumption rate | String |
| can_feco | CAN fuel economy | String |
| can_pto | CAN PTO | String |
| can_hrfc | CAN HRFC | String |
| can_dist | CAN distance | String |
| can_amt | CAN ambient air temperature | String |
| can_ect | CAN engine coolant temperature | String |
| can_rpm | CAN RPM | String |
| can_engh | CAN engine hours | String |
| can_srdist | CAN service distance | String |
| tco_dist | TCO distance | String |
| tco_trip | TCO trip | String |
| tco_vespd | TCO vehicle speed | String |
| tco_rpm | TCO RPM | String |
